Toshiba Tosvert VF-AS1 Manual do Utilizador Página 141
- Página / 312
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
E6581301
F-29
6
6. 17 Braking function
H : Braking mode selection
H
: Load portion torque input
selection
H
: Hoisting torque bias input
H
:
Lowering torque bias multiplier
H : Brake release time
H
: Creeping frequency
H
: Creeping time
H
: Braking time learning function
•Function
These parameters can be used as brake sequences for lifts and similar equipment.
To ensure smooth operation, the motor produces enough torque before the brake is released.
Title Function Adjustment range Default setting
H Braking mode selection
:Deselect
:Forward winding up
:Reverse winding up
:Horizontal operation (counter weight)
H Load portion torque input selection
:Disabled
:VI/II (voltage/current input)
:RR/S4 (potentiometer/voltage input)
:RX (voltage input)
:H enabled
:2-wire RS485 input enabled
:4-wire RS485 input enabled
:Communications option input enabled
:A1 (differential current input)
H
Hoisting torque bias input (valid
only when H=)
-~%
H Lowering torque bias multiplier ~%
H Brake release time ~ sec.
H Creeping frequency H~Hz
H Creeping time ~ sec.
H Braking time learning function
:Deselect
:Brake signal learning (0 after adjustment)
■ Starting procedure
At the run command, the inverter makes the motor produce the torque specified with parameter H. As soon as
a torque output command is issued, a brake release request signal is put out through the brake output terminal.
Upon expiration of the brake release time set with H, the motor starts to accelerate.
- E6581301Ԙ 1
- I. Safety precautions 3
- Danger 4
- II. Introduction 9
- E6581301 11
- - Contents 11
- 1. Read first 17
- 1.3.1 Names and functions 18
- 1) Outside view 18
- 1.3.2 Detaching the cover 25
- 1.4 Notes on the application 30
- 1.4.1 Motors 30
- 1.4.2 Inverters 32
- ■ Disposal 32
- Warning 33
- 1.4.4 Installation 35
- ■ Installation environment 35
- ■ How to install 36
- 2. Connection equipment 41
- 2.2 Standard connections 43
- 2.3 Description of terminals 48
- 3. Operations 55
- Status monitor mode 56
- Standard monitor mode 56
- (when the power is turned on) 56
- Setting monitor mode 56
- Deceleration 57
- 3.2.2 Panel operation 61
- 4.1 How to set parameters 64
- 5. Basic parameters 67
- CW : Automatic torque boost 69
- ■ Preset speed operation 74
- + The inverter is factory 75
- +To save the frequency 75
- HE and the set 75
- 5.6 Selecting control mode 77
- 2) Decreasing output voltage 78
- 3) Increasing starting torque 78
- 5.8 Base frequency 81
- 5.9 Maximum frequency 82
- Estimation of temperature 90
- 5.17 PWM carrier frequency 96
- Warning 97
- Surge killer 103
- 5.20 Standard default setting 107
- ( ) 109
- 5.22 EASY key function 110
- 6. Extended parameters 113
- 6.2 Input signal selection 115
- Internal command 116
- Servo lock status 120
- Command selected 123
- Operation frequency 125
- 6.8 DC braking 126
- 6.10 Jog run mode 131
- Jumping width 2 135
- Jumping width 1 135
- 6.14.1 Retry function 136
- 6.15 Drooping control 139
- Load portion torque input 141
- 6.20 PID control 145
- 6.22 Setting motor constants 148
- Setting motor constants 150
- 6.24 Torque control 152
- 6.25 Torque limit 154
- Positive torque 155
- Negative torque 155
- • Function 158
- 6.31 Pattern operation 163
- 6.32 Preset speed mode 165
- 6.33 Protection functions 166
- 6.33.3 Emergency stop 167
- H : Emergency stop 167
- 6.34 Override 175
- 6.35 Adjustment parameters 177
- Function 179
- ■ Example of setting 1 181
- ■ Example of setting 2 181
- 6.37 Tracing functions 183
- Trace data 1 184
- Trigger input 184
- 6.38 Communication function 187
- 1) 2-wire RS485 188
- 2) 4-wire RS485 190
- Host computer 191
- 6.39 My function 193
- 6.40 Traverse function 194
- 7.1 External operation 195
- B-contact switch 196
- Input terminal 196
- Inverter 196
- Programmable controller 197
- 7.2.4 Analog input filter 203
- 8.2 Monitoring the status 210
- 8.4.1 Trip code display 216
- 9.1.1 EMC directive 221
- Contact your supplier 222
- Use the 224
- EMC FILTER 226
- Ferrite core 1 227
- Shielded cable or [Note 1] 227
- Noise cut plate 228
- AIC, Fuse and Wire sizes 229
- Ｅ６５８１３００ 232
- Note on wiring 233
- 11. Table of parameters 239
- 12. Specifications 285
- E6581301 286
- ■ Outside dimensions and mass 289
- (Installation dimension) 290
- Before making a service call 295
- Cautions about cleaning 303
- 14.2 Periodical inspection 304
- ■ Check items 304
- 15. Warranty 307
- Warning 309
Manuais e produtos relacionados com Ferramentas Toshiba Tosvert VF-AS1
Ferramentas Toshiba HX7 Manual do Utilizador
(6 páginas)
(6 páginas)
Ferramentas Toshiba 1500 Plus Manual do Utilizador
(31 páginas)
(31 páginas)
Ferramentas Toshiba G8000 Manual do Utilizador
(79 páginas)
(79 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais