Toshiba TOSVERT VF-S15 series option unit Function E658183 Manual do Utilizador Página 1

E6581830 TOSVERT VF-S15 series ® option unit Function Manual CCL003Z NOTICE 1. Read this manual before

E658130 - 9 - 4.4. The maximum connection number of units 1. Maximum number of units connected to one master station (CC-Link Ver.1.10) 42 units (w

E658130 - 10 - 2. Maximum number of units connected to one master station (CC-Link Ver.2.00) 42 units (when connections are inverter only) If any ot

E658130 - 11 - 4.5. LED indicator The LEDs shows the present status of the network and module Refer to 7.3 for detail. Layout of LED L.R

E658130 - 12 - 5. Functions This option is a communication interface unit that allows the PLC program to operate, monitor and set the parameter o

E658130 - 13 - 5.2. Communication parameters for CCL003Z Title Function Description c100 Communication error detection delay time 0.0 - 100.0

E658130 - 14 - 5.3. CC-Link function setting 5.3.1. Station number setting Use parameter c120 to set station number of the inverter. Set this para

E658130 - 15 - 5.3.3. CC-Link extended setting Remote register function can be extended. Title Function Description c122* CC-Link extended selectio

E658130 - 16 - 5.4. Basic functions This clause shows the basic function of this CC-Link option using by CC-Link communication. 5.4.1. Run and fre

E658130 - 17 - 5.5. I/O signal list 5.5.1. One station is occupied (CC-Link Ver.1) (c122=0) This option occupies one station area of the buffer me

E658130 - 18 - 5.5.2. Double setting is selected (CC-Link Ver.2) (c122=1) This option occupies one station area of the buffer memory of the PLC. In

E658130 - 1 - Introduction Thank you for purchasing the “CC-Link® option (CCL003Z)” for TOSVERT VF-S15 drive. This option can connect with open fiel

E658130 - 19 - 5.5.4. Octuple setting is selected (CC-Link Ver.2) (c122=3) This option occupies one station area of the buffer memory of the PLC. In

E658130 - 20 - 5.5.5. Trip history When “Quadruple setting” or “Octuple setting” of CC-LINK V.2 is selected, the past trip information can be refe

E658130 - 21 - 5.5.6. Detail of input and output signals 1. Output signals (Master -> Inverter) The output signals from the master unit are indic

E658130 - 22 - Input function selection from the CC-Link. The function numbers selection of the RYn2 to RYn8 function valid from the command of the

E658130 - 23 - 2. Input signal (Inverter -> Master) The following shows input signals to the master unit. (The output signals for the inverter.)

E658130 - 24 - 5.5.7. Remote Register Assignment Divide the monitor code (RWw n) into half and select the monitor value 1 (RWr n) from the lower 8 b

E658130 - 25 - Address Signal Description RWwn+10 Instruction code 2 Set the command code for actions such as operation mode switching, paramet

E658130 - 26 - 2. Remote register (Inverter -> Master) RWr Address Signal Description RWr n Monitor value 1 When (RYnC) is on, the monitored

E658130 - 27 - Address Signal Description RWrn+13 Read data 3 For a normal reply, the reply data to the instruction specified by the instructio

E658130 - 28 - 5.5.8. Instruction Codes Code No. Item Description 1003H Command mode selection read 2003H Command mode selection write 0: Ter

E658130 - 2 - Handling in general Warning Prohibited Do not connect or disconnect a network cable while the drive power is on. It may lead to

E658130 - 29 - Code No. Item Description 4900H to 6999H Read parameters (RAM) To read parameters a900 to c999, 6000H is subtracted from the param

E658130 - 30 - 5.5.9. The details of an error code The following data are stored as fault history data when the inverter trip occurred. Error code

E658130 - 31 - Error code Decimal No. Hexadecimal No. Description Trip display 50 32H Analog input break detection fault e-18 51 33H CPU communicat

E658130 - 32 - 5.5.10. Description of reply code When executing the frequency setting (RYnD) or instruction code execution (RYnF), check the reply

E658130 - 33 - 5.5.11. Description of monitor code Divide the monitor code (RWw n) into half and select the monitor value 1 (RWr n) from the lowe

E658130 - 34 - 5.5.12. Description of input terminal information Data composition of input terminal information (Code No. = 0FH). Bit Terminal na

E658130 - 35 - 6. Programming examples This chapter provides programming examples which control the inverter with the PLC. Item Programming Exam

E658130 - 36 - 2. Network parameter setting of the master station Network parameters are set as below.Item Setting Conditions Start I/O No. 0000 Da

E658130 - 37 - 3. The relation between the device of the programmable controller CPU and remote I/O (RX,RY) of the remote device station is as follo

E658130 - 38 - 6.1. Program example for reading the inverter status Example 1 shows a ladder logic to read the inverter status. Y30 of the output

E658130 - 3 - Table of Contents 1. OVERVIEW ...

E658130 - 39 - 6.2. Program example for setting the operation mode Example 2 shows a ladder logic to write data in the inverter. The operation mo

E658130 - 40 - 6.3. Program example for setting the operation commands Example 3 shows a ladder logic to give a forward command to station 2 invert

E658130 - 41 - 6.5. Program example for monitoring the output frequency Example 5 shows a ladder logic to read the output frequency of station 1 in

E658130 - 42 - 6.6. Program example for parameter writing Example 6 shows a ladder logic to chang the setting of f311 of station 1 inverter to 1 f3

E658130 - 43 - 6.7. Program example for parameter reading Example 7 shows a ladder logic to read parameter f311 of station 1 inverter to D2. f311:

E658130 - 44 - 6.8. Program example for trip information reading Example 8 shows a ladder logic to read the trip information of station 1 inverter

E658130 - 45 - 6.9. Program example for resetting the inverter at inverter error Example 9 shows a ladder logic to reset the station 2 inverter.

E658130 - 46 - 6.10. Instructions 1.Programming instructions 1.1 Since the buffer memory data of the master station is kept transferred (refreshe

E658130 - 47 - 7. Unusual diagnosis 7.1. Option error The error message is displayed when there is hardware error, software error or lose of co

E658130 - 48 - 7.3. How to check the error using the LEDs The following example explains the causes of fault which may be judged from the LED statu

E658130 - 4 - 1. Overview The option allows the VF-S15 drive to be connected into a CC-Link network. CC-Link supports a maximum of 42 nodes, allowin

E658130 - 49 - 2.When two or more inverters are connected The following example explains the causes and corrective actions for fault which may be j

E658130 - 50 - 3. Communication stops during operation ▪ Check that the CC-Link units and the CC-Link dedicated cable are connected properly. (Che

E658130 - 5 - 2.1. CC-Link Version 2.1.1. CC-Link Ver. 1.10 The conventional CC-Link products, whose inter-station cable lengths have equally been

E658130 - 6 - 3. Names and functions The drawing below shows names and functions of main parts. 3.1. Outline LED indicator (See

E658130 - 7 - 4. Installation on inverter Refer to VF-S15 option adapter instruction manual (E6581838) for the installation on the inverter. Manda

E658130 - 8 - 4.3. Connection of CC-Link master unit and inverter The example of the connection of the CC-Link master unit and the inverter is show