Before UsingPreparationsOperationsMaintenanceOthersTDP-PX10DATA PROJECTOROWNER’S MANUALIn the spaces provided below, record the Model and Serial No. l
10EXEMPTION CLAUSES• Toshiba Corporation bears no responsibility in the case of damages arising from naturaldisaster such as earthquakes, lightning, e
11Before UsingOTHER INFORMATIONCopyrightsShowing or transmitting commercial imaging software or broadcast or cable-broad castingprograms with the purp
12REMOTE CONTROL BATTERIESWarningNever throw batteries into a fire.Using the batteries improperly may cause them to explode or leak and may result in
13Before Using
14CONTENTSBefore usingSAFETY PRECAUTIONS ... 2IMPORTANT SAFETY INSTRUCTIONS
15Before UsingOthersIndicators ... 46Before calling
16PreparationsChecking the package contentsPlease make sure that the following items are included in the box, along with the main unit.Ifany item is m
17PreparationsNames of each part on the main unitName :Function(1) Infrared remote sensor :Senses commands from the remote control. (2) Lens :Projects
18Names of each part on the control panel and remote controlControl panel Remote Control CAUTION• Do not look into the laserlight source of the remote
19PreparationsNote• For the remainder of this manual, buttons are referred to as follows:Selection buttons ; ENTER button Name :Main Function
2Before usingSAFETY PRECAUTIONSMODEL NAME: TDP-PX10!FCC NOTICE:This device complies with part 15 of the FCC Rules. Operation is subject tothe followin
20Label locationsParts on the rear panelCaution. use of controls or adjustments or performance of procedures other than thosespecified herein may resu
21PreparationsPreparing and using the remote controlLoading dry-cell batteries into theremote controlMRemove the battery cover.NInsert the dry-cell b
22Preparing and using the remote control (Continued)Dry-cell batteries• Before using the batteries, be sure to observe the Safety Precautions describe
23PreparationsOperating a computer using the remote controlA computer can be operated using the projector(s remote control. This function is available
24PlacementPlacement StylesAs shown in the figures below, this device can be placed in 2 different styles.The factory setting is "floor-mounted f
25PreparationsProjection Distance and SizeUse the figures, tables, and formulas below to determine the projection size and projectiondistance. (Projec
26ConnectionBefore connection• Read the owner(s manual of the device you are connecting to the projector.• Some computers cannot be used with or conne
27PreparationsConnecting with AV equipmentNote• Moving pictures played back on computers using DVD software may appear unnaturalwhen projected with th
28OperationsTurning the power on and offConnecting the power cordInsert the power cord connector into the AC INsocket of the projector.Insert the pow
29OperationsNote• The start-up screen will disappear after a moment. You can also configure the system toprevent the start-up screen from appearing. T
3Before Using- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into
30Basic operationsTurn on the power.Turn on the power by following the instructions in #Turning the power on” .Activate the connected device.Turn on
31OperationsUsing handy featuresUsing auto setting (For computer input only)This function automatically sets up the projector to the optimum state. It
32Using handy features (continued)Freezing the image (Freeze)The projected image can be frozen. This function is used to pause videoduring a presentat
33OperationsUsing the menusYou can call up on-screen menus, and make adjustments and settings using the operationbuttons on the control panel (main un
34Using the menus (continued)Image adjustment menuUse this menu to set or adjust image-related items. Items that can be set or adjusted aremarked “Yes
35OperationsDisplay setting menuNote• [Display effect] None: displays screen without special effects.Wipe: displays the next slide gradually to the ri
36Using the menus (continued)Default setting menu Note• Set the [Fan mode] to [High] when using the projector at the high altitude (higher than600m or
37OperationsDisplaying Information (Status display) Note• The mode of supported RGB signals !is shown.•[Version] shows the version of the projector’s
38Using USB MemoryConnect the USB memory to the projector and select USB inputPress INPUT button to select USB source.Plug the USB memory to the USB p
39OperationsSlideshow Mode / Display of movie filesSlideshow Mode / Display of movie files• Quick StartWhen the projector is set to the USB input and
4IMPORTANT SAFETY INSTRUCTIONSCAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONSGIVEN IN THIS OWNER'S MANUAL AND THOSE MARKED ON THE
40Using USB Memory (continued)Exit Slideshow / Stop playing movie filePress button to exit slideshow while the slideshow is in operation or to stop
41OperationsPBacking up the dataToshiba recommends that you back up the data saved in the USB! memory before use.Toshiba assumes no liability for loss
42MaintenanceAbout lampThe product’s light source is a mercury lamp that lights at increased internal pressure. Be sureto fully understand the followi
43MaintenanceLamp replacement (Continued)Unplug power cord.Wait until lamp is sufficiently cooled.Wait for at least 1 hour.Remove the lamp cover.Loose
44Lamp replacement (Continued)Notes and Precautions•The [Lamp time] item in the Status display menu indicates the time of lamp use (as arough guide).
45MaintenanceLens and main unit cleaningLens cleaning• Clean the lens with a commercially available blower and/or! lenscleaner.• The lens is easily s
46OthersIndicatorsF2: Flash 2HzState/ Problems Icon/ Messages Close MessagesLED IndicatorsTEMP LAMPEnvironment overheat OnFan lockSystem error F2 F2La
47OthersBefore calling service personnelIf you think something is wrong, check the followings before contacting customer service.Please see "Indi
48SpecificationsList of general specificationsNote• This model complies with the above specifications.• Designs and specifications are subject to cha
49OthersList of supported signals (RGB signals)This projector supports the following RGB signals. Note, however, that depending on thecomputer model,
5Before Using5. HeatThe product should be situated awayfrom heat sources such as radiators,heat registers, stoves, or otherproducts (including amplifi
50Specifications (Continued)List of supported signals (Component signals)Signal Horizontal Frequency (kHz) Vertical Frequency (Hz)480i 15.8 kHz 60 Hz
51OthersPin assignment of COMPUTER IN terminalsPin assignment of S-VIDEO terminalsPin No. Signal Name1RED2 GREEN3BLUE4NC5GND6GND7GND8GND9 VCC 5V10 N
6IMPORTANT SAFETY INSTRUCTIONS (Continued)11.Lightning stormsFor added protection for this productduring a storm, or when it is leftunattended and unu
7Before Using17.AccessoriesDo not place this product on anunstable cart, stand, tripod, bracket, ortable. The product may fall, causingserious injury
8IMPORTANT SAFETY INSTRUCTIONS (Continued)21.Replacement PartsWhen replacement parts are required,be sure the service technician hasused replacement p
9Before UsingIMPORTANT PRECAUTIONSMoisture CondensationNever operate this unit immediately after moving it from a cold location to a warm location.Whe
Comentários a estes Manuais