Toshiba SD-M1201 Manual do Utilizador descarregar pdf

SD-M1201 DVD-ROM

with REALmagic Hollywood+ Playback Card

Installation Instructions

Congratulations on your purchase of a Toshiba SD-M1201 DVD-ROM

drive and REALmagic Hollywood+ DVD/MPEG-2 Playback Card Kit.

The following information will help you in the simple installation of

your new DVD-ROM. It is assumed that you are replacing a presently

installed CD-ROM with the enclosed DVD-ROM. If this is not the case,

additional installation hardware may be required. Refer to REALmagic

Hollywood+ User’s Guide for installation instructions on the DVD/MPEG-

2 Playback Card.

CHECKING YOUR KIT PACKAGING

Please unpack your DVD kit, and assure that you have the following

items:

l Toshiba SD-M1201 SCSI DVD-ROM drive

l DVD/MPEG-2 PCI Playback Card (compatible with all graphics cards)

l 13” 3.5mm ext. audio cable

l 14” HDB15 - 9 DIN overlay cable

l S-Video to RCA video converter cable

l REALmagic™ Accessory Kit envelope

(with software, demo CD and Playback Card User’s Guide)

l SD-M1201 DVD-ROM Installation Instructions (this manual)

Additional items you may need that are not included in the kit are:

l Screwdriver

l mounting screws and mounting hardware

l SCSI interface cable

l SCSI host adapter board

l DVD/CD-ROM Sound Cable

SYSTEM REQUIREMENT

The DVD-ROM kit requires the following:

✔ 2MB of free hard disk space

✔ 16MB of RAM

✔ Pentium-based PC (or compatible), 133MHz or higher

✔ PCI 2.1 compliant expansion slot

✔ VGA Card

✔ Plug and Play BIOS support

✔ Microsoft™ Windows 95 or higher

✔ Amplified stereo speakers

1 2 3 4 5 6 7 8

Resumo do Conteúdo

Página 1 - Installation Instructions

SD-M1201 DVD-ROMwith REALmagic Hollywood+ Playback CardInstallation InstructionsCongratulations on your purchase of a Toshiba SD-M1201 DVD-ROMdrive an

Página 2 - SETTING JUMPERS

The follow steps must be performed to properly install your DVD-ROM.l Set DVD-ROM drive jumper settings.l Connect audio cable.l Install SCSI host adap

Página 3 - Connecting Cables

PRV/ALW - This jumper is used to inhibit the drive’s EJECT button.When the jumper is ON, the EJECT button will not operate.Test - This setting selects

Página 4

4If you are replacing your CD-ROM: connect DVD-ROM to the SCSIinterface connector that the CD-ROM was connected to.If DVD-ROM is not replacing a CD-RO

Página 5 - SCSI Interface Cable

5Daisy-Chaining - If the DVD-ROM you are installing is one of two ormore SCSI devices you are connecting to your system, you will need touse a custom

Página 6 - DVD-ROM FRONT PANEL

2.5 - 3.5mmSurface of side or bottom of DVD-ROM driveMounting frame of host computerMounting ScrewM36COMPLETING INSTALLATIONAfter you have connected a

Página 7 - ② Mode select jumper

DVD-ROM BACK PANELThe photo illustrates the following features of the SD-M1202 DVD-ROMback panel:①Analog audio out connector② Mode select jumper③SCSI

Página 8 - TECHNICAL SUPPORT

SD-M1201 SPECIFICATIONS DVD CD-ROMData Capacity (bytes/block) 2,048 mode 1 mode 22,048 2,336Rotational Speed (approx. rpm) 2,900 13.8 ~ 32X: 6,9008.6