Toshiba A10 Series Manual do Utilizador

TOSHIBA Satellite A10 SeriesPortable Personal ComputerUser’s Manual

Notes for use of this device in New Zealand❑ The grant of a Telepermit for a device in no way indicates Telecom acceptanceof responsibility for the co

User's ManualOPERATING BASICS4-18SettingYou can enable or disable the following settings:AutoRun ModeThe Region Select utility starts automatical

OPERATING BASICS 4-19Figure 4-11 Connecting the internal modemCAUTION: Do not pull on the cable or move the computer while thecable is connected.NOTE

User's ManualOPERATING BASICS4-20❑ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36,24, 18, 12, 9 and 6Mbit/s. (Revi

OPERATING BASICS 4-21Wireless communication IndicatorThe wireless communication indicator indicates the status of the wireless communi-cation function

User's ManualOPERATING BASICS4-22Connecting LAN cableCAUTION: The computer must be configured properly before connectingto a LAN. Logging onto a

OPERATING BASICS 4-23CAUTION: Make sure the LAN Active indicator (orange LED) is outbefore you disconnect the computer from the LAN.1. Pinch the lever

User's ManualOPERATING BASICS4-24❑ Close all port covers.❑ Use the carrying case when transporting the computer.Heat dispersalTo protect from ove

THE KEYBOARDChapter 5The KeyboardTypewriter keys ... 5-1F1 … F12 functio

THE KEYBOARD

5-1THE KEYBOARDChapter 5The KeyboardThe computer’s keyboard layouts are compatible with a 101/102-key enhancedkeyboard. By pressing some keys in combi

ATS11=90 (DTMF dialing on/off duration=90 ms)ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)❑ When used in the Auto Answer mode, the S0

User's Manual5-2THE KEYBOARDF1 … F12 function keysThe function keys, not to be confused with Fn, are the 12 keys at the top of yourkeyboard. Thes

5-3THE KEYBOARDSoft keys: Fn key combinationsThe keyboard is designed to provide all the features of the 101-key enhancedkeyboard, shown in figure 5-1

User's Manual5-4THE KEYBOARDHot keysHot keys (Fn + a function or Esc key) let you enable or disable certain features ofthe computers.Sound mute:

5-5THE KEYBOARDStandby: When you press Fn + F3, the computer enters Standby. To avoidentering Standby unexpectedly, a dialog box appears for verificat

User's Manual5-6THE KEYBOARDLCD Display Brightness: Pressing Fn + F7 increases the display brightness inincrements. When you press these hot keys

5-7THE KEYBOARDFn Sticky keyYou can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is,you can press it once, release it, and th

User's Manual5-8THE KEYBOARDNumeric modeTo turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicatorlights. Now try numeric data

5-9THE KEYBOARDTemporarily using overlay (overlay off)While using the normal keyboard, you can temporarily use the keypad overlaywithout turning it on

User's Manual5-10THE KEYBOARD

POWER ANDPOWER-UP MODESChapter 6Power and Power-Up ModesPower conditions...

General conditionsAs required by PTC 100, please ensure that this office is advised of any changes tothe specifications of these products which might

POWER ANDPOWER-UP MODES

POWER ANDPOWER-UP MODES 6-1Chapter 6Power and Power-Up ModesThe computer’s power resources include the universal AC adaptor and internalbatteries. Th

6-2User's ManualPOWER ANDPOWER-UP MODESTable 6-1 Power conditions continuedPower on Power off (no operation)AC Battery • Operatesadaptor charge

POWER ANDPOWER-UP MODES 6-3No light Under any other conditions, the indicator does not light.NOTE: If the battery becomes too hot while it is being c

6-4User's ManualPOWER ANDPOWER-UP MODESBattery packWhen the universal AC adaptor is not connected, the computer’s main powersource is a removable

POWER ANDPOWER-UP MODES 6-5**** RTC battery is low or CMOS checksum is inconsistent ****Press [F1] key to set Date/Time.CAUTION: The computer’s RTC b

6-6User's ManualPOWER ANDPOWER-UP MODES3. Never short-circuit the battery pack by contacting the terminals with a metalobject. A short-circuit ca

POWER ANDPOWER-UP MODES 6-7Care and use of the battery pack3. Make sure the battery is securely installed in the computer before attemptingto charge

6-8User's ManualPOWER ANDPOWER-UP MODES2. To ensure the battery pack maintains maximum capacity, operate the computeron battery power once a week

POWER ANDPOWER-UP MODES 6-9Charging time (hours)Battery type Power on Power offBattery pack 3600mAh 3.5 to 9 or longer about 2.64400mAh 4 to 11 or lo

TEAC CD-ROM drive CD-224E, CD-RW/DVD-ROM drive DW-224E safetyinstructionCAUTIONS: 1. The CD/DVD drive employs a laser system. To ensureproper use of t

6-10User's ManualPOWER ANDPOWER-UP MODESMonitoring battery capacityRemaining battery power can be monitored in the Power Save Modes window inPowe

POWER ANDPOWER-UP MODES 6-11Care and use of the battery pack❑ How much charge the battery contained to begin with.❑ How you use optional devices, suc

6-12User's ManualPOWER ANDPOWER-UP MODES4. Connect the universal AC adaptor to the computer and the power cord to apower outlet. The DC IN indica

POWER ANDPOWER-UP MODES 6-133. In Hibernation mode, data will be lost if you removethe battery and disconnect the universal AC adaptorbefore the save

6-14User's ManualPOWER ANDPOWER-UP MODESCAUTIONS: 1. The battery pack is a lithium-ion battery, which canexplode if not properly replaced, used,

POWER ANDPOWER-UP MODES 6-15Starting the computer by passwordTo start up the computer with the user password, follow these steps:1. Turn on the power

6-16User's ManualPOWER ANDPOWER-UP MODESPanel power offYou can set up your computer so that power turns off automatically when you closethe displ

HW SETUPChapter 7HW Setup and PasswordsHW Setup ... 7-1Accessi

HW SETUP

7-1HW SETUP ANDPASSWORDSChapter 7HW Setup and PasswordsThis chapter explains how to use TOSHIBA HW Setup program to configure yourcomputer and how to

CAUTION: This appliance contains a laser systemand is classified as a “CLASS 1 LASER PROD-UCT.” To use this model properly, read theinstruction manual

User's Manual7-2HW SETUP ANDPASSWORDSGeneralThis window displays the BIOS version and contains two buttons: Default andAbout.SetupThis field disp

7-3HW SETUP ANDPASSWORDS4. If character strings match, the password is registered and the display changesto:The password was registeredIf they do not

User's Manual7-4HW SETUP ANDPASSWORDSKey FDAfter you set a password, you can create a Key FD (diskette). If you forget the userpassword, the Key

7-5HW SETUP ANDPASSWORDSParallel/PrinterSome models are equipped with Parallel/Printer tab. This tab lets you set the ParallelPort Mode. Use the Wind

User's Manual7-6HW SETUP ANDPASSWORDSDynamic CPU Frequency ModeThis option lets you choose from the following settings:Dynamically CPU power cons

7-7HW SETUP ANDPASSWORDSTo change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer.2. The following menu will be disp

User's Manual7-8HW SETUP ANDPASSWORDSHDD Priority OptionsIf more than one HDD is installed in the computer, this option lets you set thepriority

7-9HW SETUP ANDPASSWORDSUSBUSB KB/Mouse Legacy EmulationUse this option to enable or disable USB KB/Mouse Legacy Emulation. If youroperating system d

User's Manual7-10HW SETUP ANDPASSWORDSSupervisor passwordRefer to the readme file of the Supervisor Password Utility for instructions onsetting t

OPTIONAL DEVICESChapter 8Optional DevicesPC cards ... 8-2Ins

VAROITUS. Suojakoteloa si saa avata. Laitesisältää laserdiodin, joka lähetää näkymätöntäsilmilie vaarallista lasersäteilyä.CAUTION: USE OF CONTROLS OR

OPTIONAL D EVICES

8-1OPTIONAL DEVICESChapter 8Optional DevicesOptional devices can expand the computer’s capabilities and its versatility. Thischapter describes conne

User's Manual8-2OPTIONAL DEVICESPC cardsThe computer is equipped with a PC card expansion slot that can accommodate one5 mm Type II card. Any PC

8-3OPTIONAL DEVICESRemoving a PC cardTo remove the PC card, follow the steps below.1. Click the Safety Remove Hardware icon on the Task Bar.2. Click

User's Manual8-4OPTIONAL DEVICESMemory expansionYou can install additional memory in the computer’s memory module socket toincrease the amount of

8-5OPTIONAL DEVICESMemory expansionFigure 8-3 Removing the memory module cover 6. Lift one side of the insulator sheet and fit the module’s connecto

User's Manual8-6OPTIONAL DEVICESFigure 8-4 Installing the memory module8. Seat the cover and secure it with a screw.9. Replace the battery pack a

8-7OPTIONAL DEVICESFigure 8-5 Removing the memory module6. Seat the cover and secure it with a screw and replace the battery pack.Battery packYou

User's Manual8-8OPTIONAL DEVICESExternal monitorAn external analog monitor can be connected to the external monitor port on thecomputer. The comp

8-9OPTIONAL DEVICESTVe. Select Television icon.f. Select the Video Standard list box and select the format that yourTV supports.*Please select one o

3. To prevent direct exposure to the laser beam, do not tryto open the enclosure.CAUTION: This appliance contains a lasersystem and is classified as a

User's Manual8-10OPTIONAL DEVICESFigure 8-7 The Adapter window (4) Select a resolution from the menu.Figure 8-8 Resolution menu

8-11OPTIONAL DEVICESSecurity lockA security lock enables you to anchor your computer to a desk or other heavyobject to help prevent unauthorized rem

User's Manual8-12OPTIONAL DEVICES

TROUBLESHOOTINGChapter 9TroubleshootingProblem solving process ... 9-1Preliminary chec

TROUBLESHOOTING

9-1TROUBLESHOOTINGChapter 9TroubleshootingTOSHIBA designed the computer for durability. However, should problems occur,following the procedures in t

User's ManualTROUBLESHOOTING9-2❑ Check that your diskette or CD/DVD-ROM is correctly inserted and that thediskette’s write protect tab is correct

9-3TROUBLESHOOTINGHardware If you cannot find a software problem, check your hard-ware. First run through the items in the preliminarychecklist abov

User's ManualTROUBLESHOOTING9-4Self testWhen the computer starts up, the self test will be run automatically, and thefollowing will be displayed:

9-5TROUBLESHOOTINGOverheating power downIf the computer’s internal temperature becomes too high, the computer will automati-cally shut down.Problem

vermeiden darf das Gerät nicht geöffnetwerden.ADVARSEL: Denne mærking er anbragtudvendigt på apparatet og indikerer, atapparatet arbejder med laserstr

User's ManualTROUBLESHOOTING9-6BatteryIf you suspect a problem with the battery, check the DC IN indicator as well as theBattery indicator. For

9-7TROUBLESHOOTINGHardware and system checklistPasswordProblem ProcedureCannot enter Contact your dealer.or forgot passwordNOTE: For information on

User's ManualTROUBLESHOOTING9-8• The way to replace the key-topPress the key-top until you hear a click afterremoving a metal spring from the ke

9-9TROUBLESHOOTING• Follow the steps below when a plastic spring isout of place together with a key- top.1. Remove the plastic spring from the key-t

User's ManualTROUBLESHOOTING9-103. Press from the upside until you hear a clickafter replacing the key-top to the right position.LCD panelProblem

9-11TROUBLESHOOTINGHard disk driveProblem ProcedureComputer does not Check if a diskette is in the diskette drive or aboot from hard disk CD-ROM is

User's ManualTROUBLESHOOTING9-12A foreign object in the drawer could block laserlight from reading the CD. Make sure there is noobstruction. Remo

9-13TROUBLESHOOTINGDVD-ROM driveFor more information, refer to Chapter 4, Operating Basics.Problem ProcedureYou cannot access Make sure the drive’s

User's ManualTROUBLESHOOTING9-14Check the type of CD/DVD you are using. Thedrive supports:DVD-ROM: DVD-ROM, DVD-VideoCD-ROM: CD-DA, CD-Text, Phot

9-15TROUBLESHOOTINGCheck whether the CD/DVD is dirty. If it is, wipeit with a clean cloth dipped in water or a neutralcleaner. See the Media care se

HITACHI DVD-ROM drive GDR-8082safety instructionCAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensureproper use of this product, please rea

User's ManualTROUBLESHOOTING9-16Cannot write correctly If you have trouble writing, make sure you areobserving the following precautions:• Use on

9-17TROUBLESHOOTINGSome CD/DVDs The software or hardware configuration mayrun correctly, but be causing a problem. Make sure theothers do not hardwa

User's ManualTROUBLESHOOTING9-18Diskette driveFor more information, refer to Chapter 4, Operating Basics.Problem ProcedureDrive does not There m

9-19TROUBLESHOOTINGHardware and system checklistPointing deviceIf you are using a USB mouse, also refer to the USB section in this chapter and toyou

User's ManualTROUBLESHOOTING9-20USB mouseProblem ProcedureOn-screen pointer The system might be busy. If the pointer isdoes not respond to shaped

9-21TROUBLESHOOTINGUSBRefer also to your USB device’s documentation.Problem ProcedureUSB device does Check for a firm cable connection between theno

User's ManualTROUBLESHOOTING9-22Sound systemRefer also to documentation for your audio devices.Problem ProcedureNo sound is heard Adjust the volu

9-23TROUBLESHOOTINGModemRefer to the online help files for Appendix C and D.Problem ProcedureCommunication Make sure the computer’s internal modemso

User's ManualTROUBLESHOOTING9-24Character display In data transmission, make sure the parity bitbecomes garbled and stop bit settings correspond

9-25TROUBLESHOOTINGWireless LANIf the following procedures do not restore LAN access, consult your LAN adminis-trator. For more information on wirel

CAUTION: This appliance contains a lasersystem and is classified as a “CLASS 1 LASERPRODUCT.” To use this model properly, readthe instruction manual c

User's ManualTROUBLESHOOTING9-26ChinaTOSHIBA Computer Systems (Shanghai) Co., Ltd.Bldg. 33, No. 351, Jinzang Road,Pudong New Area,Shanghai,P.R.

9-27TROUBLESHOOTINGUnited States of AmericaTOSHIBA America Information Systems,Inc.9740 Irvine BoulevardIrvine, California 92618USAIn EuropeGermany

User's ManualTROUBLESHOOTING9-28

APPENDIXESAppendixesAppendix ASpecifications ... A-1Appendix BDisplay Controll

APPENDIXES

APPENDIX A A-1Appendix ASpecificationsThis appendix summarizes the computer’s technical specifications.Physical DimensionsSize 332 (w) x 293 (d) x 33

APPENDIX AA-2User's ManualBuilt-in ModemNetwork control unit (NCU)Type of NCU AAType of line Telephone line (analog only)Type of dialing PulseTon

B-1APPENDIX BAppendix BDisplay Controller andModesDisplay controllerThe display controller interprets software commands into hardware commands thattu

User's ManualB-2APPENDIX BVideo modesThe computer supports video modes defined in the tables below. If your applicationoffers a selection of mode

B-3APPENDIX BAppendix BTable1 Video modes (VGA) continuedVideo Type Resolution Character LCD CRT Scanningmode matrix colors colors frequency(pels) V

Copyright© 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws,this manual cannot be reproduced in any form without the prior w

VAROITUS. Suojakoteloa si saa avata. Laitesisältää laserdiodin, joka lähetää näkymätöntäsilmilie vaarallista lasersäteilyä.CAUTION: USE OF CONTROLS OR

User's ManualB-4APPENDIX BTable 2 Video modes (XGA)Resolution LCD CRT Verticalcolors colors frequency (Hz)640 x 480 256/256K 256/256K 6075851008

B-5APPENDIX BAppendix BTable 2 Video modes (XGA) continuedResolution LCD CRT Verticalcolors colors frequency (Hz)640 x 480 64K/64K 64K/64K 607585100

User's ManualB-6APPENDIX BTable 2 Video modes (XGA) continuedResolution LCD CRT Verticalcolors colors frequency (Hz)640 x 480 16M/16M 16M/16M 60

B-7APPENDIX BTable 3 Video modes (Super XGA+)Resolution LCD CRT Verticalcolors colors frequency (Hz)640 x 480 256/256K 256/256K 607585100800 x 600 2

User's ManualB-8APPENDIX BTable 3 Video modes (Super XGA+) continuedResolution LCD CRT Verticalcolors colors frequency (Hz)640 x 480 64K/64K 64K

B-9APPENDIX BAppendix BTable 3 Video modes (Super XGA+) continuedResolution LCD CRT Verticalcolors colors frequency (Hz)640 x 480 16M/16M 16M/16M 60

User's ManualB-10APPENDIX B

C-1APPENDIX CAppendix CAT CommandsIn most cases, you will not need to type AT commands manually. However,there might be some occasions when you will n

User's ManualC-2APPENDIX CA Answer commandThis command instructs the modem to go off-hook and answer anincoming call.Bn Communication standard se

C-3APPENDIX C; Return to command mode. Causes the modem to return tocommand mode after dialing a number, without disconnectingthe call.S=n Dial a tele

CAUTION: This appliance contains a lasersystem and is classified as a “CLASS 1 LASERPRODUCT.” To use this model properly, readthe instruction manual c

User's ManualC-4APPENDIX CLn Monitor speaker volumeThis command sets speaker volume to low, medium, or high.L0 Low volume.L1 Low volume. (Same as

C-5APPENDIX CResult Codes:OK n=0,1ERROR OtherwiseOn Return on-line to data modeO0 Instructs the modem to exit on-line command mode and returnto data m

User's ManualC-6APPENDIX CT Select tone dialingThis command instructs the modem to send DTMF tones while dialing.Dialed digits are tone dialed un

C-7APPENDIX CX5 Enable Enable OK, RING, NO CARRIER, ERROR,NODIALTONE, BUSY, CONNECT<RATE>, RRING, NO BONGTONE,DELAYED, BLACKLISTED, REORDER,WARB

User's ManualC-8APPENDIX C&C0 The state of the carrier from the remote modem is ignored.DCD circuit is always on.&C1 DCD turns on when th

C-9APPENDIX C&Gn V.22bis guard tone controlThis command determines which guard tone, if any, to transmit whiletransmitting in the high band (answe

User's ManualC-10APPENDIX C&T0 Abort. Stops any test in progress.&T1 Local analog loop. This test verifies modem operation, as wellas the

C-11APPENDIX C\Nn Error control mode selectionThis command determines the type of error control used by the modemwhen sending or receiving data.\N0 Bu

User's ManualC-12APPENDIX C\Vn Protocol result code\V0 Disable protocol result code appended to DCE speed.\V1 Enable protocol result code appende

D-1APPENDIX DAppendix DS-registersS-registers contain the settings that determine how a number of functions of theinternal modem operate. For example,

ADVARSEL: Denne mærking er anbragtudvendigt på apparatet og indikerer, atapparatet arbejder med laserstråler af klasse 1,hviket betyder, at der anvend

User's ManualD-2APPENDIX DS0 Auto answer ring numberThis register determines the number of rings the modem will countbefore automatically answeri

D-3APPENDIX DS4 Response formatting character (user defined)This register determines the ASCII value used as the line feed charac-ter. The modem uses

User's ManualD-4APPENDIX DS7 Connection completion time-outThis register sets the time, in seconds, that the modem must waitbefore hanging up bec

D-5APPENDIX DS37 Dial line rateS37 = 0 (default) maximum modem speedS37 = 1 reservedS37 = 2 1200/75 bpsS37 = 3 300 bpsS37 = 4 reservedS37 = 5 1200 bps

User's ManualD-6APPENDIX DAT command set result codesThe following table shows the result codes.The result code summaryResult Code Numeric Descri

D-7APPENDIX DResult Code Numeric DescriptionDELAYED*2 88 Delay is in effect for the dialednumberBLACKLISTED*2 89 Dialed number is blacklistedBLACKLIST

User's ManualD-8APPENDIX D

E-1APPENDIX EAppendix EV.90The TOSHIBA internal modem uses V.90 technology. The modem is capable ofdownstream speeds of 56Kbps (kilobits per second) w

User's ManualE-2APPENDIX ETable E-1 Result codes for a V.90 connectionNo. Result code Description70 CONNECT 32000 EC* Connection at 32000 bps72

E-3APPENDIX E*EC stands for the Error Control method, which appears only when the extendedresult codes configuration option is enabled. EC is replaced

xxiiiTable of ContentsPrefaceManual contents ... xxxiConventions ...

User's ManualE-4APPENDIX E

F-1APPENDIX FAppendix FInternal Modem GuideThis appendix describes how to install and the remove the internal modem.CAUTION: Do not disassemble the co

F-2User's ManualAPPENDIX F9. Secure the cover with one screw.Removing the internal modemTo remove the internal modem, follow the steps below.1. S

G-1APPENDIX GAppendix GWireless LANCard SpecificationsForm Factor - Mini PCI TypeIIICapability - I EEE 802.11 Standard for Wireless LANSWi-Fi (Wireles

G-2User's ManualAPPENDIX G- Band2.4GHz (2400-2483.5 MHz) (Revision B)Modulation Technique - DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK (Revision B)- OFDM-B

G-3APPENDIX GWhen installing Wireless LAN Cards, the channel configuration is managed asfollows:❑ For wireless clients that operate in a Wireless LAN

G-4User's ManualAPPENDIX GWireless Channels Sets (Turbo Mode)Frequency Range 5150-5850 MHz NoteChannel ID42 5210 US only *150 5250 US only *158 5

H-1APPENDIX HAppendix HAC Power Cord andConnectorsThe power cord’s AC input plug must be compatible with the various internationalAC power outlets and

H-2User's ManualAPPENDIX HThe following illustrations show the plug shapes for the U.S.A. and Canada, theUnited Kingdom, Australia and Europe.USA

APPENDIX II-1Appendix IParts NumbersThe computer configuration and parts numbers, printed on a label on the bottom ofthe computer, indicate the CPU, L

xxivCommunications... 1-7Security...

User’s ManualAPPENDIX IConfigurationsThe following table shows the computer configuration indicated on a label. Shaded areas indicate abbrevi

Glossary-1GLOSSARYGlossaryThe terms in this glossary cover topics related to this manual. Alternate namingis included for reference.AbbreviationsAC:

Glossary-2GLOSSARYanalog signal: A signal whosecharacteristics such as amplitude andfrequency vary in proportion to (are ananalog of) the value to be

Glossary-3GLOSSARYBbackup: A duplicate copy of files keptas a spare in case the original isdestroyed.batch file: A file that can be executedfrom t

Glossary-4GLOSSARYcapacity: The amount of data that canbe stored on a magnetic storagedevice such as a diskette (floppy disk)or hard disk. It is us

Glossary-5GLOSSARYcomponents: Elements or parts (of asystem) which make up the whole(system).computer program: A set of instruc-tions written for

Glossary-6GLOSSARYdevice driver: A program that controlscommunication between a specificperipheral device and the computer.The CONFIG.SYS file contai

Glossary-7GLOSSARYescape guard time: A time before andafter an escape code is sent to themodem which distinguishes betweenescapes that are part of

Glossary-8GLOSSARYcomputer itself, external disk drives,etc. See also software and firmware.hertz: A unit of wave frequency thatequals one cycle per

Glossary-9GLOSSARYcoating is etched into characterforming segments with leads thatextend to the edge of the glass.Applying a voltage between the gla

xxvRestoring the preinstalled software from theProduct Recovery CD-ROM ... 3-12Chapter 4 Operating

Glossary-10GLOSSARYpermanently storing information.Turning the computer’s power offdoes not alter data stored in nonvola-tile memory.numeric keypad ov

Glossary-11GLOSSARYPparallel interface: Refers to a type ofinformation exchange that transmitsinformation one byte (8 bits) at a time.See also seri

Glossary-12GLOSSARYSSCSI: Small Computer SystemInterface is an industry standardinterface for connection of a variety ofperipheral devices.SD cards: S

Glossary-13GLOSSARYsubpixel: Three elements, one red,one green and blue (RGB), that makeup a pixel on the color LCD. Thecomputer sets subpixels ind

Glossary-14GLOSSARYGlossary

IndexIndex-1INDEXIndexlocation of vents 2-2settings 4-24CPU, See ProcessorDDiskette drive 1-3using 4-2view 2-10Display 1-5, 2-7automatic power off 1-8

User's manualIndex-2INDEXwork habits 3-4Expansion memory, See MemoryFFn + Ctrl(enhanced keyboard simulation) 5-3Fn + Enter 5-3Fn + Esc (sound mut

IndexIndex-3INDEXLLAN 1-7connecting 4-22disconnecting 4-22jack 2-5LAN active indicator 2-4link indicator 2-5problems 9-24LCD, See Display, Video modes

User's manualIndex-4INDEXkeyboard 9-7LAN 9-24LCD panel 9-10memory expansion 9-21modem 9-23monitor external 9-22mouse, USB 9-20overheating power d

IndexIndex-5INDEXWireless LAN 1-7problems 9-25using 4-19

xxviChapter 5 The KeyboardTypewriter keys ... 5-1F1 … F12 function keys

xxviiChapter 7 HW Setup and PasswordsHW Setup ... 7-1Accessing

xxviiiCD-RW/DVD-ROM drive ... 9-14DVD-R/-RW drive ...

xxixAppendix IParts Numbers ... I-1GlossaryIndex

FCC informationProduct Name : Satellite A10Model number : PSA10FCC notice "Declaration of ConformityInformation"This equipment has been test

xxx

xxxiPrefaceCongratulations on your purchase of the Satellite A10 series computer. Thispowerful notebook computer provides excellent expansion capabi

xxxiiChapter 4, Operating Basics, includes instructions on using the following devices:Touch Pad, USB diskette drive, optical media drives, modem, wi

xxxiiiKeysThe keyboard keys are used in the text to describe many computer operations. Adistinctive typeface identifies the key top symbols as they ap

xxxiv

xxxvGeneral PrecautionsTOSHIBA computers are designed to optimize safety, minimize strain and withstandthe rigors of portability. However, certain pre

xxxviCentral Processing Unit ("CPU") PerformanceDisclaimerCPU Performance in your computer product may vary from specifications under thefol

INTRODUCTIONChapter 1IntroductionEquipment checklist ... 1-1Hardware ...

INTRODUCTION

1-1INTRODUCTIONChapter 1IntroductionThis chapter provides an equipment checklist, and it identifies the computer’sfeatures, options and accessories.

FCC conditionsThis device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:1. This device may not cause har

1-2User's ManualINTRODUCTION• Online manual❑ Product Recovery CD-ROMDocumentation• Satellite A10 Series Portable Personal Computer User's M

1-3INTRODUCTIONMemorySlots 128, 256 or 512 MB memory modules can be installed in thetwo memory slots for a maximum of 1 GB system memory.Video RAM A

1-4User's ManualINTRODUCTION• CD-ROM Mode 1, Mode 2• CD-ROM XA Mode 2 (Form1, Form2)• Enhanced CD (CD-EXTRA)• CD-G (Audio CD only)• Addressing Me

1-5INTRODUCTIONDVD-R/-RW drive Some models are equipped with a full- size DVD-R/-RWdrive module that lets you record data to rewritable CD/DVDs as w

1-6User's ManualINTRODUCTIONPointing deviceBuilt-in Touch Pad A Touch Pad and control buttons in the palm rest enablecontrol of the on-screen poi

1-7INTRODUCTIONSpecial featuresCommunications Modem An internal modem provides capability for data and faxcommunication. It supports V.90 (V.92). Re

1-8User's ManualINTRODUCTIONHot keys Key combinations let you quickly modify the systemconfiguration directly from the keyboard without running a

1-9INTRODUCTIONBattery save mode This feature lets you save battery power. You can specifythe Power Save Mode in the Running on batteries item ofthe

1-10User's ManualINTRODUCTIONHW Setup This program lets you customize your hardware settingsaccording to the way you work with your computer andt

1-11INTRODUCTIONOptionsYou can add a number of options to make your computer even more powerfuland convenient to use. The following options are avai

Modem warning noticeConformity StatementThe equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection t

1-12User's ManualINTRODUCTION

THE GRAND TOURChapter 2The Grand TourFront with the display closed ... 2-1Left side...

THE GRAND TOUR

THE GRAND TOUR 2-1Chapter 2The Grand TourThis chapter identifies the various components of your computer. Become familiarwith each component before y

User's ManualTHE GRAND TOUR2-2Wireless Slide this switch toward the left of the computer to turncommunication off Wireless LAN function. Slide it

THE GRAND TOUR 2-3Right sideHeadphone jack This jack lets you connect digital speakers or a stereoheadphone (16 ohm minimum). When you connect a digi

User's ManualTHE GRAND TOUR2-4DVD-R/-RW drive Some models are equipped with a full-size DVD-R/-RWdrive module that lets you record data to rewrit

THE GRAND TOUR 2-5Link indicator This indicator glows green when the computer is connect- (green) ed to a LAN and the LAN is functioning properly.Par

User's ManualTHE GRAND TOUR2-6UndersideFigure 2-5 shows the underside of the computer. Make sure the display is closedbefore turning over your co

THE GRAND TOUR 2-7Front with the display openFigure 2-6 shows the front of the computer with the display open. To open thedisplay, slide the display

Telephone company proceduresThe goal of the telephone company is to provide you with the best service it can. Inorder to do this, it may occasionally

User's ManualTHE GRAND TOUR2-8Stereo speakers The speakers emit sound generated by your software aswell as audio alarms, such as low battery cond

THE GRAND TOUR 2-9keyboard indicatorsCD-ROM This indicator glows green when the computer is drive accessing a diskette in the diskette drive or a dis

User's ManualTHE GRAND TOUR2-10Arrow mode When the Arrow mode indicator lights green, you canuse the keypad overlay (gray labeled keys) as cursor

THE GRAND TOUR 2-11NOTES: 1. The external diskette drive should be placed on a flat,horizontal surface when in use. Do not set the drive on anincline

User's ManualTHE GRAND TOUR2-12DVD-ROM drives and media are manufactured according to the specifications of sixmarketing regions. When you purcha

THE GRAND TOUR 2-13Code Region1. Canada, United States2. Japan, Europe, South Africa, Middle East3. Southeast Asia, East Asia4. Aust

User's ManualTHE GRAND TOUR2-144. Australia, New Zealand, Pacific Islands, Central America, South America,Caribbean5. Russia, Indian Su

GETTING STARTEDChapter 3Getting StartedSetting up your work space ... 3-1General conditions

GETTING S TARTED

3-1GETTING STARTEDChapter 3Getting StartedThis chapter provides basic information to get you started using your computer. Itcovers the following top

Japan regulationsRegion selectionIf you are using the computer in Japan, technical regulations described in theTelecommunications Business Law require

User's ManualGETTING STARTED3-2General conditionsIn general, if you are comfortable, so is your computer, but read the following tomake sure your

3-3GETTING STARTEDSeating and postureThe height of your chair in relation to the computer and keyboard as well as thesupport it gives your body are

User's ManualGETTING STARTED3-4LightingProper lighting can improve legibility of the display and reduce eye strain.❑ Position the computer so tha

3-5GETTING STARTEDConnecting the universal AC adaptorAttach the universal AC adaptor when you need to charge the battery or you wantto operate from

User's ManualGETTING STARTED3-6Opening the displayThe display panel can be rotated in a wide range of angles for optimal viewing.1. Slide the dis

3-7GETTING STARTED2. Press and hold the computer’s power button for two or three seconds.Figure 3-5 Turning on the powerStarting up for the first t

User's ManualGETTING STARTED3-83. Click start then click Turn Off Computer. From the Turn Off Computer menuselect Turn Off.4. Turn off the power

3-9GETTING STARTEDStarting HibernationNOTE: You can also enable Hibernation by pressing Fn + F4. SeeChapter 5, Keyboard, for details.To enter Hibern

User's ManualGETTING STARTED3-10CAUTION: Do not turn the computer or devices back on immediately.Wait a moment to let all capacitors fully discha

3-11GETTING STARTED❑ Saves power by shutting down the system when the computer receives noinput or hardware access for the duration set by the Syste

Instructions for IC CS-03 certified equipment1 The Industry Canada label identifies certified equipment. This certification meansthat the equipment

User's ManualGETTING STARTED3-12Restarting the computerCertain conditions require that you reset the system. For example, if:❑ You change certain

OPERATING BASICSChapter 4Operating BasicsPointing devices ... 4-1Using th

OPERATING BASICSMoving the computer ... 4-23Heat dispersal ...

OPERATING BASICS 4-1Chapter 4Operating BasicsThis chapter gives information on basic operations including using the pointingdevices, USB diskette driv

User's ManualOPERATING BASICS4-2Double-click: Tap twiceDrag and drop: Tap to select the material you want to move. Leave yourfinger on the Touch

OPERATING BASICS 4-3Disconnecting 3 1/2" diskette driveWhen you have finished using the diskette drive, follow the procedures below todisconnect

User's ManualOPERATING BASICS4-4Loading discsTo load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7.1. a. When the power is on,

OPERATING BASICS 4-52. Pinch the drawer gently and pull until it is fully opened.Figure 4-5 Pulling the drawer open3. Lay the CD/DVD, label side up,

User's ManualOPERATING BASICS4-6CAUTIONS: 1. Do not touch the laser lens. Doing so could causemisalignment.2. Be careful to keep foreign matter

OPERATING BASICS 4-7Writing CDs on CD-RW/DVD-ROM driveCAUTIONS: 1. When the drawer pops open slightly, wait a moment tomake sure the CD/DVD has stopp

3 The standard connecting arrangement (telephone jack type) for this equipment isjack type(s): USOC RJ11C.The IC registration number of the modem is

User's ManualOPERATING BASICS4-8Before writing or rewritingPlease observe the following points when you write or rewrite the data.❑ We recommend

OPERATING BASICS 4-9❑ Do not perform any of the following actions:• Operate the computer for any other function, including use of a mouse orTouch Pad,

User's ManualOPERATING BASICS4-10❑ Any change or loss of the recorded contents of CD-R/RW or DVD-R/-RW discthat may be caused by writing or rewri

Read/write function chartDisc type CD-R CD-RW DVD-R DVD-RW DVD-RAM DVD+R DVD+RWReadWriteDrag’n Drop CD*1No NoNo NoNo No NoYes YesYes YesYesYesYesYesYe

User's ManualOPERATING BASICS4-12❑ Based on TOSHIBA's limited compatibility testing, we suggest the followingmanufacturers of CD-R/RW and DV

OPERATING BASICS 4-13Writing CD/DVDs on DVD-R/-RW drive❑ Since the disc is based on the DVD standard, it might be filled with dummy dataif the written

User's ManualOPERATING BASICS4-14❑ Make sure writing or rewriting is completed before going into standby/hibernation.❑ Set the computer on a leve

OPERATING BASICS 4-15Media careThis section provides tips on protecting data stored on your CD/DVDs anddiskettes.Handle your media with care. The foll

User's ManualOPERATING BASICS4-166. Magnetic energy can destroy the data on your diskettes. Keep your diskettesaway from speakers, radios, televi

OPERATING BASICS 4-173. Click the icon with the primary mouse button to display a list of regions thatthe modem supports. A sub menu for telephony loc